Electric submersible pump types, applications, and selection tips
Release Time:
2026-11-20
Author:
LBAPRO
Article overview
This in-depth guide explains electric submersible pump types, real-world applications, a formula-based selection method, EU compliance requirements, lifecycle cost data, and a maintenance troubleshooting workflow — giving engineers and buyers the detail needed to specify with confidence.
Table of contents
- 1. What is an electric submersible pump?
- 2. How an electric submersible pump works
- 3. Main types of electric submersible pump
- 4. Key applications across industries
- 5. How to select the right electric submersible pump — step-by-step
- 6. Lifecycle cost analysis and energy efficiency
- 7. Installation, maintenance, and fault diagnosis
- 8. EU and German regulatory requirements
- 9. Frequently asked questions
What is an electric submersible pump?
An electric submersible pump is a hermetically sealed motor-and-pump unit designed to operate fully submerged in fluid, converting electrical energy directly into hydraulic energy at the source. Unlike surface-mounted pumps that pull liquid upward, the ESP pump system pushes fluid to the surface, eliminating the suction-lift limitation and enabling operation at depths exceeding 300 m.
The defining advantage is efficiency. Because the pump motor unit sits at the fluid source, it avoids cavitation caused by long suction lines and delivers higher hydraulic efficiency — typically 60–85 % depending on design. That matters in Germany, where energy costs and ErP Directive compliance make pump efficiency a procurement priority in 2026.
For a comprehensive technical background, see this electric submersible pump overview from Wikipedia.
Why are ESP systems preferred over jet pumps for deep installations?
Jet pumps lose efficiency rapidly beyond 8–10 m of suction head. A borehole pump or deep well pump operating at 50–200 m delivers 30–45 % more hydraulic efficiency in the same duty point, according to pump-engineering literature published through 2025. The tradeoff is a higher upfront cost and the need to pull the entire unit for servicing — a factor that shapes the total lifecycle cost calculation covered in section 6.
Where does the technology come from?
Submersible pump technology was commercialised in the oil industry in the 1920s and was later adapted for municipal water extraction and wastewater handling. Today it underpins everything from residential borehole water supply in rural Baden-Württemberg to multiphase oil well pump systems in offshore fields — a breadth of application few other pump categories can match.
How an electric submersible pump works
The operating principle combines an electric motor, a shaft, and one or more centrifugal pump stages in a single sealed assembly. Power travels down a submersible cable to the motor; the motor drives the shaft, which spins the pump impeller; centrifugal force accelerates fluid outward and upward through each successive stage.
Think of it like a stack of fans inside a pipe — each stage adds pressure, so stacking more stages raises total head without changing diameter. This modular stage design is what allows the same motor frame to serve a 20 m garden well or a 300 m industrial borehole simply by adding or removing stages.
Key internal components
- Hermetically sealed motor: Oil- or water-filled stator windings, rated for continuous submersion.
- Pump impeller: Cast from stainless steel, bronze, or engineered polymers depending on fluid chemistry.
- Diffuser/bowl assembly: Converts velocity head into pressure between stages.
- Mechanical seal: Prevents fluid ingress at the shaft-motor interface — the most common failure point.
- Check valve: Prevents back-flow and water hammer when the pump stops.
What is pump installation depth and why does it matter?
Pump installation depth determines motor cooling, cavitation margin, and cable sizing. The motor is cooled by fluid flowing past its casing; if the installation depth is too shallow or the water level drops below the pump intake, thermal damage can occur within minutes. For borehole applications in Germany, a minimum submergence of 1.5–3 m above the pump intake is recommended to maintain adequate cooling and prevent air entrainment.

Main types of electric submersible pump
Not all submersible pumps are identical. The right type depends on the fluid handled, required head, flow rate, and installation environment. Here is a structured overview of the most common categories.
| Type | Typical head range | Flow range | Primary use case | Notes |
|---|---|---|---|---|
| Deep well / borehole pump | 30–300 m | 1–50 m³/h | Groundwater extraction, domestic supply | Slim 4″ / 6″ / 8″ diameters |
| Industrial submersible pump | 10–80 m | 10–500 m³/h | Process water, cooling water, dewatering | Often ATEX-rated for hazardous zones |
| Wastewater / sewage pump | 5–40 m | 5–300 m³/h | Sewage lift stations, stormwater | Vortex or single-channel impeller |
| Oil well pump (ESP) | 300–3,000 m equivalent | 50–5,000 bbl/day | Artificial lift in oil production | High-temperature rated motors |
| Drainage / dewatering pump | 5–25 m | 5–200 m³/h | Construction sites, basements, ponds | Portable, can handle light solids |
| Vertical turbine pump | 20–200 m | 50–10,000 m³/h | Large-scale water extraction, irrigation | Motor can be surface-mounted |
Shielded deep well pump — a specialised variant
A shielded deep well pump uses a canned (shielded) motor where the rotor runs directly in the pumped liquid, eliminating conventional bearing lubrication. This design significantly reduces mechanical wear in clean, cold groundwater and is well suited to German domestic boreholes where water temperatures stay below 20 °C year-round.
ATEX vs. standard IP ratings — when does it matter?
Standard industrial submersible pumps carry an IP68 rating, meaning continuous immersion protection. ATEX-certified units add explosion protection for use in potentially explosive atmospheres — relevant for petrochemical facilities, biogas plants, and certain mining applications. Never use a standard IP-rated downhole pump in an ATEX zone; the consequences are legally and physically severe.
Key applications across industries
The electric submersible pump serves a remarkably wide spectrum of industries. Understanding which application category your project falls into is the first step in narrowing down the correct type and specification.
Water extraction and groundwater supply
Municipal waterworks and rural agricultural operations in Germany rely heavily on borehole pumps for groundwater abstraction. A typical agricultural setup in Bavaria might require a 6-inch borehole pump delivering 15–25 m³/h against 80 m of total head, running 10–16 hours per day during growing season. The water extraction pump must comply with DIN EN 14 183 for borehole pump testing and carry CE marking.
Oil and gas artificial lift
In petroleum engineering, the ESP pump system is the dominant artificial-lift technology for high-volume oil wells. The downhole pump is set several hundred metres below the perforations; multistage centrifugal pump bowls lift the produced fluid to the wellhead. According to research compiled on ESP systems in oil production, ESPs can lift over 5,000 barrels per day in a single string — a capacity no other artificial-lift method easily matches at that depth.
Wastewater and stormwater management
Wastewater submersible pumps are engineered to handle solids-laden fluid without clogging. The vortex impeller design keeps solids in suspension rather than passing them through the impeller. German municipal wastewater standards (DIN EN 12050) specify minimum free passage diameters — typically 50 mm for domestic applications and up to 100 mm for commercial lift stations.
Industrial process and cooling water
Factories, data centres, and power plants use industrial submersible pumps for coolant circulation, process water supply, and emergency flood control. These applications demand continuous-duty ratings, stainless steel wetted parts, and variable-frequency drive (VFD) compatibility to manage varying load profiles efficiently.
How to select the right electric submersible pump — step-by-step
Selection errors are expensive. A pump that is oversized wastes energy and shortens motor life through excessive start-stop cycling; an undersized unit simply cannot meet demand. The following method works for water extraction pump and industrial submersible pump applications alike.
- Determine total dynamic head (TDH).
TDH = Static head (m) + Friction losses in pipes (m) + Pressure at discharge point (m equivalent).
Worked example: Static head = 60 m, pipe friction over 80 m of 50 mm diameter pipe at 10 m³/h ≈ 4.8 m (using Hazen-Williams C = 120), discharge pressure = 1.5 bar = 15.3 m. TDH = 60 + 4.8 + 15.3 = 80.1 m. - Define required flow rate (Q).
For domestic supply: 2–4 m³/h per household. For agricultural drip irrigation: consult crop-water demand charts. For industrial process: measure actual consumption and add a 15 % safety margin. - Match pipe diameter to flow velocity.
Recommended velocity: 0.8–1.5 m/s in rising mains. At 10 m³/h, a 50 mm (DN50) pipe gives ~1.4 m/s — acceptable. Stepping down to 40 mm gives ~2.2 m/s, increasing friction losses by approximately 90 % — a costly mistake in borehole installations. - Check borehole diameter vs. pump OD.
Allow at least 15 mm clearance between the borehole casing ID and the pump OD for adequate cooling flow. A 4-inch (101.6 mm) pump requires a minimum 5-inch (127 mm) casing. - Verify motor power and electrical supply.
In Germany: 230 V / 50 Hz single-phase for motors up to 1.5 kW; 400 V / 50 Hz three-phase for larger units. Confirm that cable cross-section compensates for voltage drop over installation depth — maximum permissible voltage drop: 5 % per IEC 60364. - Select based on the pump curve intersection.
Plot your system curve (TDH vs. Q) against the manufacturer's pump curve. The duty point must fall within the preferred operating range (typically 70–110 % of best efficiency point) to protect pump efficiency and service life. - Confirm fluid properties.
Sand content, pH, temperature, and chemical composition dictate material selection. Groundwater with >100 mg/L suspended solids requires a sand-fighter design; corrosive media require AISI 316 stainless or duplex steel wetted parts.
"Selecting a submersible pump purely on price without considering the system curve and fluid chemistry is the single most common cause of premature failure in borehole installations. The duty point must sit within the manufacturer's preferred operating range — operating outside this zone accelerates impeller wear, increases motor temperature, and can void the warranty."
— Adapted from electric submersible pump engineering, ScienceDirect engineering topics review, 2025
Lifecycle cost analysis and energy efficiency
Purchase price typically represents only 15–25 % of a pump's total lifecycle cost. The dominant cost driver is energy consumption — a reality that makes pump efficiency the most important financial variable for any continuous-duty installation.
Annual energy cost calculation
Annual energy cost (€) = Motor power (kW) × Operating hours per year × Electricity tariff (€/kWh). At the 2026 German commercial electricity rate of approximately €0.28/kWh, a 2.2 kW borehole pump running 2,000 hours/year costs roughly €1,230 per year in electricity alone.
| Scenario | Motor power | Efficiency class | Annual hours | Annual energy cost | 5-year cost |
|---|---|---|---|---|---|
| Residential borehole | 0.75 kW | IE3 (ErP compliant) | 800 h | ~€168 | ~€840 |
| Agricultural irrigation | 2.2 kW | IE3 | 2,000 h | ~€1,232 | ~€6,160 |
| Industrial process | 11 kW | IE4 + VFD | 6,000 h | ~€18,480 | ~€92,400 |
| Industrial process | 11 kW | IE2 (no VFD) | 6,000 h | ~€21,560 | ~€107,800 |
The IE4 + VFD scenario saves approximately €15,400 over five years compared with the IE2 baseline — a payback period of under 18 months for the VFD investment in most German industrial applications. That is a compelling argument for specifying higher-efficiency motors, even when the initial procurement budget is under pressure.
ErP Directive and minimum efficiency requirements
Since January 2023, EU Regulation 2019/1781 mandates IE3 as the minimum efficiency class for motors from 0.75 kW upward; IE2 is only permitted with a variable-speed drive. When specifying any industrial submersible pump for a German installation, confirm that the motor bears the IE class marking and that the ErP energy efficiency index (EEI) meets the applicable product category benchmark.
Installation, maintenance, and fault diagnosis
Even the best-specified pump will fail prematurely if installed or maintained incorrectly. Field experience consistently shows that most downhole pump failures trace back to three root causes: dry running, voltage imbalance, and mechanical seal degradation.
Float switch failure — diagnosis and repair
The float switch (Schwimmerschalter) is the first line of defence against dry running. Symptoms of failure include the pump running continuously without shutting off at high level, or failing to start despite adequate water level. Diagnosis steps:
- Disconnect power and test float switch continuity with a multimeter — resistance should be near zero in the closed position, open circuit in the open position.
- Inspect the float body for cracks or water ingress; a waterlogged float will not rise correctly.
- Check the cable for abrasion against the borehole casing — a common issue in deep installations.
- Replace with an equivalent rated unit (IP68, correct cable length, matching voltage rating).
Impeller blockage — clearing and prevention
Blocked impellers are the leading cause of reduced flow in wastewater applications. If flow drops suddenly but motor current remains normal or slightly elevated, impeller blockage is the most probable cause. Pull the pump, disassemble the pump volute, and clear any debris manually. For recurring blockage, consider upgrading to a larger free-passage impeller or installing an upstream screen.
Mechanical seal leakage — detection and service intervals
A leaking mechanical seal allows fluid into the motor cavity, causing winding insulation breakdown within hours. Early warning signs include increased motor temperature, fluctuating insulation resistance on a megohmmeter test, or oil contamination in the pumped fluid. Industry best practice is to test insulation resistance annually; values below 1 MΩ indicate the pump should be pulled for seal inspection. Spare mechanical seal kits are typically consumable items and are not covered under standard manufacturer warranty beyond the first 12 months.
Routine maintenance schedule
- Monthly: Check motor current draw against nameplate; listen for abnormal vibration or noise at the wellhead.
- Annually: Megohmmeter insulation test; inspect cable insulation at surface; test float switch; check pressure vessel pre-charge.
- Every 3–5 years: Pull pump, inspect impellers and wear rings, replace mechanical seal, re-grease bearings if accessible.
EU and German regulatory requirements
Regulatory compliance is non-negotiable for any electric submersible pump sold or installed in Germany. Overlooking certification requirements can result in product recalls, insurance voidance, and liability exposure.
Electrical standards and plug/socket requirements
German installations operate at 230 V / 50 Hz (single-phase) or 400 V / 50 Hz (three-phase). Portable submersible pumps with a plug connection must use the Schuko (Type F, CEE 7/4) standard — not the two-pin Type C connector used in some export markets. Three-phase industrial installations use CEE industrial connectors per IEC 60309. Any pump supplied with an incompatible plug must be rewired before installation; using an adapter is not permitted under DGUV Regulation 3 electrical safety rules.
CE, GS, and TÜV certification
CE marking is mandatory for all pump products placed on the EU market; it confirms conformity with the Machinery Directive (2006/42/EC), Low Voltage Directive (2014/35/EU), and EMC Directive (2014/30/EU). The voluntary GS mark (Geprüfte Sicherheit) — issued by notified bodies including TÜV Rheinland and TÜV SÜD — signals that an independent German test laboratory has verified the CE declaration. For public procurement and large industrial projects in Germany, GS or TÜV certification is frequently a mandatory tender requirement, not merely a preference.
Noise emission limits
Surface-mounted control panels and ancillary equipment for submersible pump systems must comply with the Machinery Directive's noise provisions. For residential borehole pump installations within 3 m of a property boundary, German noise ordinances (TA Lärm) typically require the system's airborne noise output to stay below 50 dB(A) during daytime operation. Specify this requirement explicitly when sourcing pump control panels — it is frequently overlooked in import documentation.
Frequently asked questions
Frequently asked questions
Q: What is the difference between a submersible water pump and a jet pump?
A: A submersible water pump is submerged at the water source and pushes fluid upward; a jet pump sits at the surface and pulls via suction. Submersible pumps are more efficient beyond 8–10 m depth, avoid cavitation issues, and are quieter. Jet pumps are easier to service but limited to shallow wells. For boreholes deeper than 15 m, an electric submersible pump is almost always the better choice.
Q: How deep can an electric submersible pump operate?
A: Standard residential borehole pumps are rated for pump installation depths of 20–150 m. Industrial and wellbore pump systems designed for oil production or deep groundwater extraction can operate beyond 300 m. The limiting factors are cable voltage drop, motor cooling, and mechanical pressure on the pump casing — all of which must be engineered for the specific installation depth.
Q: What certifications should I require for a pump installed in Germany?
A: At minimum, require CE marking, compliance with EU Regulation 2019/1781 (ErP / IE3 motor efficiency), and IP68 protection rating. For public-sector projects or industrial applications, additionally require GS certification from a TÜV-accredited test body. ATEX certification is mandatory if the installation is in an explosive-atmosphere zone (e.g., biogas plants, fuel storage areas).
Q: How do I calculate the correct pump size for my borehole?
A: Calculate total dynamic head (TDH) = static head + pipe friction losses + discharge pressure equivalent. Then establish required flow rate with a 15 % safety margin. Plot these values as a system curve and select a pump whose curve intersects within 70–110 % of the best efficiency point. Always verify that the borehole casing allows at least 15 mm clearance around the pump OD for cooling.
Q: Can I use a variable-frequency drive (VFD) with any submersible pump?
A: Most modern electric submersible pump motors are VFD-compatible, but you must confirm this with the manufacturer before installation. VFD use requires a motor rated for inverter duty and a screened submersible cable to suppress high-frequency interference. Never run a standard motor on a VFD without verification — doing so can damage winding insulation and void the warranty. Under current EU ErP rules, IE2 motors must be paired with a VFD to meet minimum efficiency requirements.
Conclusion
The electric submersible pump remains one of the most versatile and energy-efficient fluid-moving technologies available in 2026 — but only when correctly specified, installed, and maintained. From choosing between a borehole pump for a residential well and a multistage ESP pump system for an oil well, the selection process demands precise TDH calculations, fluid chemistry analysis, compliance with German and EU electrical standards, and a clear-eyed assessment of lifecycle energy costs. Apply the step-by-step selection method and lifecycle cost framework in this guide, and you will be equipped to make a technically sound procurement decision that performs reliably for years.
Latest News
Need Help with Your Pump Project?
Get expert support for pump selection, system design, and quotation.
Mobile website
TikTok